pentair control panel not commanding pumps

Pentair control panel not commanding pumps how to#
Pentair control panel not commanding pumps install#
Pentair control panel not commanding pumps update#
Pentair control panel not commanding pumps manual#

Once you are at v4.0.0,, updates can be done over the air (wirelessly). The easiest way is to ensure that your MSP is at v4.0.0 or higher. If the available version is higher, then you should upgrade. You can check your current version by going into Config -> System Info.

Pentair control panel not commanding pumps update#

With Releasse 4.7.0 the MSP (Main System Processor) update is unified for OmniLogic, OmniPL and OmniHub.

Wired (Remote) Terminal – HLWALLMOUNT / Wireless (Remote) Terminal - HLWIRELESS.

MPP (Main Panel Processor / Main Board).

MSP (Main System Processor / Main System Touch Display).

Hayward provides updates for firmware for the following components: Hayward OmniLogic Controller Release Notes for Firmware Revision R1.2.0 MSP/WMT Hayward OmniLogic Troubleshooting Guide Residential Technical Updates for Pool Professionals shows all the pump models that work with Omni-Based systems. The links below are for helpful Hayward OmniLogic resources:

1.19 OmniLogic App Sunset/Sunrise Times Static.

1.16 No Water Flow Timeout FlowSensor Error.

1.14 T-CELL Voltage Sensor Short Chlorinator 1.

Pentair control panel not commanding pumps how to#

1.12 How to Delete a Site from Hayward Omnilogic Site List.1.11 Omni/VS Pump HUA Not Visible to the Omni Control.1.10 OmniLogic Drops Connection Between Pool and Pump.1.6 Hayward OmniLogic light issues after 4.X FW update.1.3 OmniLogic App Shows Incorrect Equipment State.1.1.4.1 4.3.0 Features and Enhancements.Replace impeller or pump to rectify but also inspect sump pit to eliminate debris that could damage new item. Inspect impeller for broken or missing blades.

Pentair control panel not commanding pumps manual#

After the pump shuts off the water column keeps moving upward for a moment, then slams downĪdjust float switch per the owner's manual so it shuts off before it starts sucking air. It is causing the water to move too fast in the pipe. You may be using a pump that is higher in horsepower than you need.

Pentair control panel not commanding pumps install#

Install a section of flexible rubber hose (like radiator hose) between the pump discharge and the discharge pipe to provide noise insulation. Install a section of flexible rubber hose (like radiator hose) between the pump discharge and the discharge pipe to provide vibration insulation.Ĭheck valve slams shut causing a bang just after pump shuts off Can also try hanging the pipe with an exhaust hanger from an auto parts store. Put insulating foam between pipe and wall and/or joists. Only an effluent style pump with tethered style switch should be used if laundry water is to be pumped.ĭischarge pipe is rattling or banging against wall and/or floor joists Soap scum on probes of electronic float switch can make contact even when water is gone 'fooling' the switch. Laundry water builds up soap scum on the float switch which will impede float movement. Using vertical style or electronic probe style float switch in sump pit that gets laundry water If pit is not overflowing, no real issue is present but you may wish to have a spare pump on hand in case the pump fails from over-use. If it is, but water level in pit does not drop, then you simply have more water coming into the pit than the pump can move out. See section 'Motor is just humming - not running”Ĭheck discharge to be sure water is being ejected from pit. Remove obstacle or relocate pump or switch to avoid the obstacle.įor tethered style floats, ensure there is a minimum of 3' of cord between float ball and cord mounting bracket.įor vertical style floats, check adjustment of rubber stopper under the float ball at the bottom of the float rod. Inspect pit for anything that can cause the float ball to get stuck and not settle to its 'off' position.

Plug pump cord into piggyback connector on back/side of float switch plug. Put the combination into a single receptacle of an outlet.

Pump cord and float switch cord are plugged in separately If you test your pump using the piggyback plug mentioned above, and it still works, you can replace the float switch and keep using the same pump. The float switch is typically the first thing to fail. Be sure to disconnect the power to the pump before servicing it. You will need to remove the sump basin cover and assess your pump to determine the cause. This either means you have a lot of water coming in or the float switch is stuck in the ON position.